The bed leveling problem
1. First check whether the fixing screws of the beam on the top of the gantry frame (refer to the picture, there are 4 pieces in total) are tightened, and whether there is a tilt in the installation, you can try to use a wrench to reinforce it.
2. Check again whether the fixing screws of the hotbed (refer to the picture) are tightened, you can try to use a wrench to reinforce it.
3. After checking the reinforcement, restore the factory settings first, refresh the firmware, and then try to run Auto Z-align and Leveling Bed, that is, re-leveling.
Firmware: https://sovol3d.com/pages/download
Flash firmware video tutorial: https://www.youtube.com/watch?v=p6l253OJa34&list=PLR9JZRQ01t7lgsgEfBYiTzZKhnPCwkUZ6&index=27
Leveling tutorial: https://www.youtube.com/watch?v=_YOPNDGI8mk&list=PLR9JZRQ01t7lgsgEfBYiTzZKhnPCwkUZ6&index=14&t=11s
4. Disassemble the hotbed part, measure them separately with a ruler, and compare the isolation columns, hotbed and bottom slider plate. Check if the length of the 5 isolation columns (refer to picture) under the hotbed are the same.
Disassembly hotbed tutorial: https://www.youtube.com/watch?v=AD0WjAVfhRc&list=PLR9JZRQ01t7lgsgEfBYiTzZKhnPCwkUZ6&index=29
5. Use a ruler to measure the hotbed and the bottom slider board separately, and check whether three A4 papers can pass through the gap (refer to the picture).
The under-extrusion problem
It may be that the nozzle has a blockage situation or the leveling is not adjusted properly, the nozzle and the hot bed are too close to each other can also have an effect. You can use a needle to clean the filaments that may be blocked on the nozzle under heating, and use the smallest wrench to clean the filaments that may be clogged in the heat break part like sending filaments. First restore the factory settings and then refer to the leveling video for re-leveling.
Leveling video: https://www.youtube.com/watch?v=_YOPNDGI8mk&list=PLR9JZRQ01t7lgsgEfBYiTzZKhnPCwkUZ6&index=15&t=11s
Thermal Runaway and Heating Failure
1. Check whether the heating wire and thermistor wire of the hotbed are firmly plugged in and whether they are damaged.
2. You can change the heating wire and thermistor of the hotbed to the position of the nozzle, and then set the heating to 60 degrees to try. (Because of the exchange, it is necessary to set the heating nozzle, but it is the hotbed that actually heats up.)
3. Please use a multimeter to check whether there is 24V DC voltage output in the position in the picture after operating the hotbed command.
If the print sticks, it reaches some high and then does a massive layer shift like the whole Z assembly is bent because it happen always at the same point and the print fails.
You can slow down the printing speed to print, and then check whether the coupling that fixes the Z-axis motor shaft and the screw rod and the screw that fixes the T-nut of the screw rod are loose. Lock them tightly to ensure that the motor shaft and screw are moving synchronously. Then check whether the screw rod is bent. If it is bent, remove it and put it on the table for comparison with a ruler, and then provide us with a picture of the bend for confirmation.
The heat creep problem (The print fails in some middle points, sometimes higher or lower points.)
1. Because the uneven heat dissipation of bi-metal may cause thermal creep, the temperature of the melted PLA of the bi-metal heat break will be about 10-20 lower than the normal temperature. We have also verified that the nozzle temperature of 175-180° can melt and extrude ordinary PLA normally. You can check whether the retraction distance is too long, the standard is about 0.5mm-0.8mm, and you can also increase the nozzle temperature by 5-10° appropriately for printing.
2. If the nozzle is blocked, you can use a needle to clean the filaments that may be clogged on the nozzle under heating, and use the smallest wrench to clean up the filaments that may be clogged in the heat break part like sending filaments.
3. You can disassemble the extrusion mechanism and clean up the filaments left on the gear. Check whether the extrusion gear is loose and the discharge is not smooth, and lock the screw that fixes the gear. The extrusion is not smooth, and the situation of blockage will affect the printing.
Reference video: https://www.youtube.com/watch?v=mFIRd1ZH81I&t=3s
After a power outage, the display is blank. It powers on and goes to a blank blue screen.
1. You can first remove the screen and put it on the table. Except for the screen cable, keep it away from contact with other metal parts of the machine, and then try flashing the firmware.
2. Refer to the part of flashing the motherboard firmware in the video, and format the TF card and set the format according to the requirements.
Firmware: https://sovol3d.com/pages/download
Reference video:https://www.youtube.com/watch?v=vqaneIsSauM
Collider when goes the auto home
1. The x-axis timing belt is too tight, you need to loosen the timing belt properly.
2. The sensitivity of the x-axis is not appropriate, you can increase or decrease it appropriately.
Reference video: https://drive.google.com/drive/folders/18QIKk514ca-xP7NLjLCiwjyvVsjSfxmE?usp=sharing
No response to the impact for X-axis goes auto home
1. Because it adopts the limitless switch mode, it is normal that occasionally there will be no response to the impact and slow response during the auto home process. Please follow the steps to adjust it.
2. If the belt is too loose or too tight, it will affect the auto home. First adjust the tightness of the belt to an appropriate level (generally, it can move smoothly), and then try to auto home.
3. If there is still no response to the impact or the response is slow, you can increase the sensitivity value of the corresponding direction (X or Y), increase by 1~5 each time, return to the previous level and press save, and then auto home again for testing.
(Operation steps: Configuration→Advanced Settings→TMC Drivers→Sensorless Homing→Store Settings)
Motherboard fan noise
Try to disassemble the cover of the motherboard, and check whether there are foreign objects inside the motherboard fan or abnormal noise caused by cables interfering with the motherboard fan.
The X-rail bearings are noisy and unstable, and there is noise when the z-axis prints quickly.
These are normal phenomena and do not affect printing. The machine itself is like this. If you feel that the friction is too much, you can add a little lubricant.
The Z axis does not run smoothly
1. Check whether the screw fixing the wire rod on the coupling (1 in the picture) is loose, and ensure that the wire rod and the motor run synchronously.
2. Check whether the T-shaped nut (2 places in the picture) is loose, whether there are sundries, and whether the bearing at the optical axis (3 in the picture) has any sundries.
3. Is there any problem with printing random models? Please provide a video of the z-axis not running smoothly when printing.
Coupling cannot be locked
Adjust the position and lock the screws on the coupling tightly (as shown in the picture). The lower screw is to lock the motor shaft, the upper screw is to lock the wire rod.
During auto home, the z-axis direction will only move upwards.
1. Is the sensor light on? If not, check to see if the connection wires are loose.
2. If the light is on, you can initialize the machine and try again.
The specifications of the two extruder fans on the SV06 (hot end & parts cooling fans)
Axial flow fan 24V 4010 (wiring with terminals) 4010 Hydraulic axial flow fan 24V 5500 rpm ±15%, 2.5 terminals 100mm outside the red and black frame
80 comments
Falk Haupt
Habe am 30.09.23 über Amazon den sovol SV06Plus Drucker gekauft und 05.10. auch erhalten. Leider fehlt die Speicherkarte. Wie können die mir helfen? MfG Haupt
Habe am 30.09.23 über Amazon den sovol SV06Plus Drucker gekauft und 05.10. auch erhalten. Leider fehlt die Speicherkarte. Wie können die mir helfen? MfG Haupt
Grant Clinch
The SD card failed, I bought a 64Gb replacement, formatted it correctly, and it wont even recognize it has a card in the slot. The old card will not show any files. I tried flashing it with updated firmware, still nothing.
the cold end heat soaks after a few hours, and glues the filament into the tube.
So far, this printer has been an utter liability, and all the forums are no help either, with others experiencing this problem.
If anyone can enlighten me, I’d like to get it working.
The SD card failed, I bought a 64Gb replacement, formatted it correctly, and it wont even recognize it has a card in the slot. The old card will not show any files. I tried flashing it with updated firmware, still nothing.
the cold end heat soaks after a few hours, and glues the filament into the tube.
So far, this printer has been an utter liability, and all the forums are no help either, with others experiencing this problem.
If anyone can enlighten me, I’d like to get it working.
Bradley
Hi sovol my printer is trying to move of its own x and y axis when beginning some prints everytime it try’s to do this it makes a very loud humming noise. I rest it to default settings and reconfigured everything it still try’s to go off of its own axis any ideas on how to fix this.
Hi sovol my printer is trying to move of its own x and y axis when beginning some prints everytime it try’s to do this it makes a very loud humming noise. I rest it to default settings and reconfigured everything it still try’s to go off of its own axis any ideas on how to fix this.
tony
HOT END WILL NOT HEAT MORE THAN 195 DEG. SO CAN’T USE PETG FILERMENT ???????
HOT END WILL NOT HEAT MORE THAN 195 DEG. SO CAN’T USE PETG FILERMENT ???????
Alex Martinez
Replaced my heat throat unit on my sv06 plus under warranty about a month back ever since I have no layer adhesion it prints the project but layers don’t stick best way to describe it as flaky took the same Goode file and ran it on a sv01plus came out fine I will re tear down the unit today if I have time and check the gears heat throat all that was sent to me has their been a fault batch of bi metal heat throat
Replaced my heat throat unit on my sv06 plus under warranty about a month back ever since I have no layer adhesion it prints the project but layers don’t stick best way to describe it as flaky took the same Goode file and ran it on a sv01plus came out fine I will re tear down the unit today if I have time and check the gears heat throat all that was sent to me has their been a fault batch of bi metal heat throat
Colin DALE
Hi scoop I need a new bed lead where do I get one thanks Colin
Hi scoop I need a new bed lead where do I get one thanks Colin
Guillem Jacquet
Tenim una Sovol SV06 i volem imprimir una peça amb mides 200×200×15 mm i comença a imprimir la peça descentrada i no hi cap.
Tenim una Sovol SV06 i volem imprimir una peça amb mides 200×200×15 mm i comença a imprimir la peça descentrada i no hi cap.
KorayTurna
Hello, I have a with my Sovol SV06. After I make the Steps of Leveling and it was OK and try to print the test 3Dbency.gcode on the TF card the Extruder press on the Baseplate and make deep scratches and it was so tight that the extruder jammed.
Now the Base plate have big scratches and demolished.
Whats the Problem and what can I do?
Hello, I have a with my Sovol SV06. After I make the Steps of Leveling and it was OK and try to print the test 3Dbency.gcode on the TF card the Extruder press on the Baseplate and make deep scratches and it was so tight that the extruder jammed.
Now the Base plate have big scratches and demolished.
Whats the Problem and what can I do?
FRANCISCO
Hello, I need help, my Sovol SV06 Plus has a filament jam in the extruder and I can’t get the TPU filament out of the extruder. This has never happened to me and I have to hand in a job. How can I solve that? Do you have any instructions for disassembling the extruder and removing the filament?
Thank you
Hello, I need help, my Sovol SV06 Plus has a filament jam in the extruder and I can’t get the TPU filament out of the extruder. This has never happened to me and I have to hand in a job. How can I solve that? Do you have any instructions for disassembling the extruder and removing the filament?
Thank you
yudah vizel
Hi Team
1. i want to add filament sensor in the instraction i need to connect it to the “DET port” but it alrady in use , so where do i need to connect it ?
2. there is open connector ( white with 2 pins ) that is not in use on the right of the exstroder , what does it for ?
Hi Team
1. i want to add filament sensor in the instraction i need to connect it to the “DET port” but it alrady in use , so where do i need to connect it ?
2. there is open connector ( white with 2 pins ) that is not in use on the right of the exstroder , what does it for ?
junk
Your products are total junk and your support sucks. look at all of the comments below.
Your products are total junk and your support sucks. look at all of the comments below.
Joshua Schmidt
Sv06 Plus won’t start. It seems that it is stuck on the opening screen. I have tried redownloading the firmware, but it has not seemed to work. I am not sure what to do and would appreciate any suggestions.
Sv06 Plus won’t start. It seems that it is stuck on the opening screen. I have tried redownloading the firmware, but it has not seemed to work. I am not sure what to do and would appreciate any suggestions.
Nahuel Eubel
Hi, I have bought a Sovol S06 and sadly one of the motor axis broke in half. I would like to replace it. As an artist I find this product really usefull.
Kind regards
Hi, I have bought a Sovol S06 and sadly one of the motor axis broke in half. I would like to replace it. As an artist I find this product really usefull.
Kind regards
Degilson Ribeiro dos Santos
Vocês tem perfil do prusa slicer para Sovol 06, para nos enviar?
Vocês tem perfil do prusa slicer para Sovol 06, para nos enviar?
Alex
Hello, I wanted to update the firmware on my sovol sv06 but unfortunately the screen remains blue can you help me?
I followed all the instructions on the site did not help
Hello, I wanted to update the firmware on my sovol sv06 but unfortunately the screen remains blue can you help me?
I followed all the instructions on the site did not help
Martin Browning
What is the email address for warranty problems? Order 40904 just received clogged, scored magnetic plate, extruder very worn and will not extrude.
What is the email address for warranty problems? Order 40904 just received clogged, scored magnetic plate, extruder very worn and will not extrude.
Luis Hernandez
I try to turn on the printer and doesnt work, it was turned off and now Im trying to turn on and just dont turns on
I try to turn on the printer and doesnt work, it was turned off and now Im trying to turn on and just dont turns on
edgar torres
worst support I ever found to be honest.
Take an eternity to respond. I regret this purchase.
worst support I ever found to be honest.
Take an eternity to respond. I regret this purchase.
Jonas
i need a new cable from the mainboard to the extruder where can i get this?
i need a new cable from the mainboard to the extruder where can i get this?
D1g174L
i got a sv006 and in a couple of months the nozzle broke off and i cant remove the threads from the nozzle what should i do or just buy a new one
i got a sv006 and in a couple of months the nozzle broke off and i cant remove the threads from the nozzle what should i do or just buy a new one
Noelani
Terry McIntyre
M. Miller
I bought a V6 just before last Christmas, and up until last week I rarely had any complaints. Then suddenly, I kept having failure after failure, either the filament would jam in the extruder, or the nozzle. I noticed that the last failure I had, the extruder had freed itself, but the strings that were coming out looked like a serrated blade of a knife. Is it possible that the hotend is loosing heat and the heat sensor isn’t picking it up?
I bought a V6 just before last Christmas, and up until last week I rarely had any complaints. Then suddenly, I kept having failure after failure, either the filament would jam in the extruder, or the nozzle. I noticed that the last failure I had, the extruder had freed itself, but the strings that were coming out looked like a serrated blade of a knife. Is it possible that the hotend is loosing heat and the heat sensor isn’t picking it up?
ade
Tiziano Passerini
The printer is stuck in the boot stage. After turning it on, the display only shows the splash screen and remains stuck there. Nothing can be done to operate the printer. I suspect I may need to flash the firmware on the touchscreen. The support web page recommends contacting Sovol, because no firmware is available for download. The printer is an S06 plus.
The printer is stuck in the boot stage. After turning it on, the display only shows the splash screen and remains stuck there. Nothing can be done to operate the printer. I suspect I may need to flash the firmware on the touchscreen. The support web page recommends contacting Sovol, because no firmware is available for download. The printer is an S06 plus.
David Greenlee
Benjamin szyszka
matthew bonafede
just following the leveling guide in my sv06 manual. step 4 is where it went wrong. when clicking level bed the machine appeared to check one maybe two spots and said it was done. tried to restart the leveling process but now i vant get through step one now. machine says “endstopsz”. so far this is not a good experience. i have know idea what to do. Sovol?
just following the leveling guide in my sv06 manual. step 4 is where it went wrong. when clicking level bed the machine appeared to check one maybe two spots and said it was done. tried to restart the leveling process but now i vant get through step one now. machine says “endstopsz”. so far this is not a good experience. i have know idea what to do. Sovol?
Omar
I received my printer, and it will not move much on the z-axis. Troubleshooting has not resulted in a fix. I would like a replacement unit. I have sent multiple emails to info@sovol3d.com and have not received a response in more than 48 hours. Should I be using another email address to get help?
I received my printer, and it will not move much on the z-axis. Troubleshooting has not resulted in a fix. I would like a replacement unit. I have sent multiple emails to info@sovol3d.com and have not received a response in more than 48 hours. Should I be using another email address to get help?
Omar
I received my printer, and it will not move much on the z-axis. Troubleshooting has not resulted in a fix. I would like a replacement unit. I have sent multiple emails to info@sovol3d.com. Should I be using another email address to get help?
I received my printer, and it will not move much on the z-axis. Troubleshooting has not resulted in a fix. I would like a replacement unit. I have sent multiple emails to info@sovol3d.com. Should I be using another email address to get help?
D BLANE
Vincenzo Pollino
I purchased the Sovol SV 06 3D printer on your site, which will arrive as soon as possible, order 36731 dated May 20, 2023. I would need the manual in Italian to be sent to me together with the shipment, if it is not provided with the shipment.
I purchased the Sovol SV 06 3D printer on your site, which will arrive as soon as possible, order 36731 dated May 20, 2023. I would need the manual in Italian to be sent to me together with the shipment, if it is not provided with the shipment.
Maik Sauer
I wanted to update the firmware on my sovol sv06 but unfortunately the screen remains blue can you help me?
I wanted to update the firmware on my sovol sv06 but unfortunately the screen remains blue can you help me?
Christopher Ostrom
MY THERMISTOR just broke off on my sv06 plus hotend is there a way to fix this or can I use regular thermistors? what should I do
MY THERMISTOR just broke off on my sv06 plus hotend is there a way to fix this or can I use regular thermistors? what should I do
Lukasz
Hey, I have a problem with planetary gear extruder, it doesn’t bite filament and there is no extrusion(only when I push filament by hand).
Hey, I have a problem with planetary gear extruder, it doesn’t bite filament and there is no extrusion(only when I push filament by hand).
Matheus Gabriel
I am having serious problems with clogging, I have set all the settings according to the manual, I have tried to reduce the retraction, I have tried several different slicers, including the sovol slicer itself, I have already disassembled and reassembled the extruder, it simply does not stop clogging ,80% the prints clog up, how can we solve this problem, it’s very annoying, I’ve tried everything and it doesn’t solve it, I need to use the printer
I am having serious problems with clogging, I have set all the settings according to the manual, I have tried to reduce the retraction, I have tried several different slicers, including the sovol slicer itself, I have already disassembled and reassembled the extruder, it simply does not stop clogging ,80% the prints clog up, how can we solve this problem, it’s very annoying, I’ve tried everything and it doesn’t solve it, I need to use the printer
Jeff Wade
My SV06 has a MINTEMP: E1 error. After power off/on, shows err under nozzle temp. When I move the extruder cable on the top of the extruder slightly, it will show a temperature reading. Any movement again makes it show err.
My SV06 has a MINTEMP: E1 error. After power off/on, shows err under nozzle temp. When I move the extruder cable on the top of the extruder slightly, it will show a temperature reading. Any movement again makes it show err.
prfesser
Clarification: after inserting filament, the printer hangs. It keeps telling me to heat the nozzle, and when I press that button and it comes to temperature, it tells me to insert the filament again. It goes back and forth between ‘heat nozzle’ and ‘insert filament’, with no way to back out except to turn off and turn on again.
Clarification: after inserting filament, the printer hangs. It keeps telling me to heat the nozzle, and when I press that button and it comes to temperature, it tells me to insert the filament again. It goes back and forth between ‘heat nozzle’ and ‘insert filament’, with no way to back out except to turn off and turn on again.
prfesser
I am a complete beginner, this is my first attempt at 3D printing. My SV06 Plus powers up fine,the bed levels fine, I can select an item to print. I insert the filament…and it hangs there.
After a few moments the nozzle temp begins to drop. The “heat nozzle” button comes up, I touch it, and am then back to “insert filament”. There does not seem to be any way to back out of the screen, back to the home screen. Please help.
I am a complete beginner, this is my first attempt at 3D printing. My SV06 Plus powers up fine,the bed levels fine, I can select an item to print. I insert the filament…and it hangs there.
After a few moments the nozzle temp begins to drop. The “heat nozzle” button comes up, I touch it, and am then back to “insert filament”. There does not seem to be any way to back out of the screen, back to the home screen. Please help.
Aussie
Hi, how can we purchase spare SV06 motherboards? They aren’t listed on the website?
Hi, how can we purchase spare SV06 motherboards? They aren’t listed on the website?
Tom Evans
Everything is working fine with my SV06 but I’m not sure about one thing. When the nozzle purges before beginning a print it just leaves a small pile of filament in the front-left corner of the plate. Is that normal? If I’m to alert to grab this little pile as soon as it appears the nozzle will drag it into the first layer.
Everything is working fine with my SV06 but I’m not sure about one thing. When the nozzle purges before beginning a print it just leaves a small pile of filament in the front-left corner of the plate. Is that normal? If I’m to alert to grab this little pile as soon as it appears the nozzle will drag it into the first layer.
Tom Evans
Everything is working fine with my SV06 but I’m not sure about one thing. When the nozzle purges before beginning a print it just leaves a small pile of filament in the front-left corner of the plate. Is that normal? If I’m to alert to grab this little pile as soon as it appears the nozzle will drag it into the first layer.
Everything is working fine with my SV06 but I’m not sure about one thing. When the nozzle purges before beginning a print it just leaves a small pile of filament in the front-left corner of the plate. Is that normal? If I’m to alert to grab this little pile as soon as it appears the nozzle will drag it into the first layer.
Robert McCann
SV06 Plus issue found and explains a lot of the issues related to “X axis” problems. I put vesconite bearings on my machine and on z and y axis very quite no issue smooth. However on the x axis i kept getting a stiff response, jumpy in appearance and every start stop was a clunk sound. Upon further investigation I found the spacing for the x axis rod bar ends to measure 1.942" outside of rods at the extruder the the rods measure 1.95" when there is a little more heat from the machine things smooth out a little but a cold start on the machine throws off the auto align and will not set bed properly. I would like a fix to this issue sooner than later pending your response to address this issue i will wait 4 days before posting on face book page.
SV06 Plus issue found and explains a lot of the issues related to “X axis” problems. I put vesconite bearings on my machine and on z and y axis very quite no issue smooth. However on the x axis i kept getting a stiff response, jumpy in appearance and every start stop was a clunk sound. Upon further investigation I found the spacing for the x axis rod bar ends to measure 1.942" outside of rods at the extruder the the rods measure 1.95" when there is a little more heat from the machine things smooth out a little but a cold start on the machine throws off the auto align and will not set bed properly. I would like a fix to this issue sooner than later pending your response to address this issue i will wait 4 days before posting on face book page.
Robert McCann
SV06 Plus issue found and explains a lot of the issues related to “X axis” problems. I put vesconite bearings on my machine and on z and y axis very quite no issue smooth. However on the x axis i kept getting a stiff response, jumpy in appearance and every start stop was a clunk sound. Upon further investigation I found the spacing for the x axis rod bar ends to measure 1.942" outside of rods at the extruder the the rods measure 1.95" when there is a little more heat from the machine things smooth out a little but a cold start on the machine throws off the auto align and will not set bed properly. I would like a fix to this issue sooner than later pending your response to address this issue i will wait 4 days before posting on face book page.
SV06 Plus issue found and explains a lot of the issues related to “X axis” problems. I put vesconite bearings on my machine and on z and y axis very quite no issue smooth. However on the x axis i kept getting a stiff response, jumpy in appearance and every start stop was a clunk sound. Upon further investigation I found the spacing for the x axis rod bar ends to measure 1.942" outside of rods at the extruder the the rods measure 1.95" when there is a little more heat from the machine things smooth out a little but a cold start on the machine throws off the auto align and will not set bed properly. I would like a fix to this issue sooner than later pending your response to address this issue i will wait 4 days before posting on face book page.
Francis DUFOUR
Good morning,
good start it’s perfect! the SV06 PLUS works very well the print quality is very correct.
nothing to say I just have a remark the motor of the X axis is very hot! 🤔
the SVplus23 serial number 327104 engine X ref: 42BYGH1603-A-20DN
the measured temperature 80° without the radiator; with the fan and the heatsink 55° is a lot
I don’t know if it is the Vref which is in question or the motor? (everything is OK no hard point the X axis slides perfectly well greased)
I changed the voltage to go to the original 1.15 at 0.8V no difference!
I feel like the motor is undersized for torque.
I make very nice prints but the life of the engine is compromised at a temperature of 80°
Good morning,
good start it’s perfect! the SV06 PLUS works very well the print quality is very correct.
nothing to say I just have a remark the motor of the X axis is very hot! 🤔
the SVplus23 serial number 327104 engine X ref: 42BYGH1603-A-20DN
the measured temperature 80° without the radiator; with the fan and the heatsink 55° is a lot
I don’t know if it is the Vref which is in question or the motor? (everything is OK no hard point the X axis slides perfectly well greased)
I changed the voltage to go to the original 1.15 at 0.8V no difference!
I feel like the motor is undersized for torque.
I make very nice prints but the life of the engine is compromised at a temperature of 80°
Brian Waites
Hello, Sovol SV6 Plus. The X axis motor is running very hot is that normal?
Thank you
Hello, Sovol SV6 Plus. The X axis motor is running very hot is that normal?
Thank you
Innovative Wings
This is the 2nd time weve used this printer. After 18 hours of run time, the X motor is running at 100 Celsius, the Y at 50 Celsius.
Is this a hardware problem or motor problem ?
Belt tension is slack. Linear bearings appear to be smooth.
Do we need to be worried ? Do we need a new part ?
This is the 2nd time weve used this printer. After 18 hours of run time, the X motor is running at 100 Celsius, the Y at 50 Celsius.
Is this a hardware problem or motor problem ?
Belt tension is slack. Linear bearings appear to be smooth.
Do we need to be worried ? Do we need a new part ?
Iordanis Kouroutzidis
Hi i Just received my Sovol SV6 Plus and after my first print
the display is blank white and the printer dose not work.It power ok ut nothing just white display . I tried to reflash with the latest firmware SV06V2.0.0A_2.24 but no go
Hi i Just received my Sovol SV6 Plus and after my first print
the display is blank white and the printer dose not work.It power ok ut nothing just white display . I tried to reflash with the latest firmware SV06V2.0.0A_2.24 but no go
mark
sv06 blue knob is jerking back and forth help
sv06 blue knob is jerking back and forth help
Jose Andrade
I bought the new SV06Plus and am not able to print one single file.
Temperature of the nozzle is showing -39 (minus thirty-nine) e material got stuck after nozzle and extruder.
I bought the new SV06Plus and am not able to print one single file.
Temperature of the nozzle is showing -39 (minus thirty-nine) e material got stuck after nozzle and extruder.